neil.mckillop.org

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Blink Electricity Monitor ======
**Summary:** Using an [[https://www.arduino.cc/|Ardunio]] to count the number of blinks from the electricity meter in the flat and eventually convert that into live and historical electricity usage graphs.  On the meter I have (a EDMI ES-10B), one blink represents 1/1000th of a [[wp>Kilowatt-hourkWh]].
==== The hardware ====
It's a really simple circuit, basically connect the light dependent resitor (LDR) to the 5V pin on the Ardunio, then connect back to GND with a 100k resistor between the LDR and GND.  Connect the analog data pin (A0) just after the LDR.

{{:pasted:20210405-172619.png|Generated with https://www.circuit-diagram.org/editor/}}

Then, upload some code to the Ardunio to count the number of blinks.  You might need to tweak the delay and the sensorValue depending on your electric meter LED type.  These values worked for me.

<code python>
int sensorPin = A0;
int sensorValue = 0;
int blinkCount = 0;
int cutOff = 600;

void setup() {
  Serial.begin(9600);
}

void loop() {
  sensorValue = analogRead(sensorPin);
  if(sensorValue > cutOff) {
    String strSensorValue = String(sensorValue);
    blinkCount++;
    String output = strSensorValue + " (" + blinkCount + ")";
    Serial.println(output);
    delay(100);
  }
  delay(100);
}
</code>

That gives me the data in the format:
<code>
Apr 05 22:07:28 977 (3787)
Apr 05 22:07:32 976 (3788)
Apr 05 22:07:36 978 (3789)
Apr 05 22:07:39 976 (3790)
Apr 05 22:07:43 976 (3791)
Apr 05 22:07:47 975 (3792)
</code>

To dump this to a file, on the Linux box (or Raspberry Pi) the Arduino is plugged into, you need to use ''stty'' set the baud rate, then just use cat to read directly from the Ardunio (I also use ''ts'' to prefix each line with a timestamp):
<code bash>
stty -F /dev/ttyACM0 9600
cat -s /dev/ttyACM0 | awk NF | ts > electricmeter.log
</code>

If you have any issues with permissions, make sure your user is in the dialout group.


Each line corresponds with a blink of the meter, so I use some PHP to basically count the number of lines in a minute (this runs in a cron job every minute):

<code php>
<?php
$data = `tail -n 100 /tmp/electric_meter.log`;
$lines = explode("\n", $data);
$current_ts = date("H:i", strtotime("-1 minute"));
$mycounter = 0;
foreach($lines as $line) {
        $fields = explode(" ", $line);
        if(is_array($fields) and sizeof($fields)>3) {
        $datetime = date("H:i", strtotime($fields[2]));
        $luminosity = $fields[3];
        $counter = $fields[4];
        if(date("H:i", strtotime($datetime)) == $current_ts) {
                $mycounter++;
        }
        }
}
$full_payload = "kwh used=$mycounter";

$url = INFLUX_SERVER_ADDRESS;
$ch = curl_init($url);
curl_setopt($ch, CURLOPT_RETURNTRANSFER, true);
curl_setopt($ch, CURLOPT_POSTFIELDS, $full_payload);
$response = curl_exec($ch);
curl_close($ch);
</code>

That data is dumped to an influxdb every minute, then plotted in Grafana:
{{:pasted:20210405-221628.png}}
neil.mckillop.org

User Tools

Site Tools

Page Tools
